Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!
My iPhone, brand new and has the factory seal on the phone.
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=140417537868&ssPageName=STRK:MESELX:IT#ht_500wt_1154
My car is soo dirty :dapprove: the C L I O badge was on it when i bought it and i didn't like it then either but it has grown on me now.
1.2 looks even smarter in the flesh :approve:
like the sound of £10 a corner :) and i think i will measure the arch gap with the 1 inch lips they have already and see what is possible once the centre bore is sorted.
I will be putting new lips on and as yet haven't decided which width to go for. Possibly 3 inch for the rears and a smaller maybe 1.5 or 2 at the front.
Was considering putting the mark fish lowering springs on too if i can get hold of some to make the wheels fill the arches a bit more.
Yeh the offset is et 33 which is already going to come out quite a bit as its on a trophy which is et 43. Adding the 20mm spacer to that will cause me problems.
They are BBS RM wheels, a lot will probs say not because turinis are almighty but after seeing a set with red centres and chrome lip...
I am looking at a set of wheels that are VW fitment (4x100, 57.1 centre)
What is the easiest/cheapest way to get these to fit ? H+R do 20mm adaptors but for all four wheel is going to cost about £210, would i be able to get the bores machined out for less than that ? or is there another way ?
That looks exactly the same as what I'm using and it doesn't seem wide or deep enough to effectively clamp the flange on the centre section to the decat.
Think I will give the heavy duty ebay one a go, worth a shot for a fiver.
Sounds good, never seem to be many RS clios when I normally go :(
1. Meganelady
2. Jamesev
3. Brian (maybe, will confirm nearer the date)
4. Dansmotorsport
5. Vdust182
6. Telfords_Lurk (maybe, will confirm nearer the date)
7. Coral (maybe)
8. Keef (maybe)
9. Lora (will check my shifts at work...
Last night the exhaust clamp (fitted by kwik fit) connecting my decat to centre section fell off :(
I put another one on today the same as the last one but it doesn't seem to fit very well. The exhaust is a BTB system and the flange is quite small so it doesn't tighten up too well.
Are...
The gearbox on my 182 has never had smooth changes ever since I bought it and to try and cure it I will soon be fitting the group N engine mounts and powerflex dogbone bushes.
However last night when doing some "spirited" driving when I changed from first into second at ~6.5K rpm it was...
Right i have recently had a new exhaust put on to my trophy (BTB cat back with yozza decat) with new gasket set aswell. However i think it is leaking when on power from 2-4K. The noise i can hear seems to come from the footwells so i am pretty sure it is the cat-manifold join.
This is quite...
Seen your car a few times at french car night. When you drove off tonight i thought exhaust sounded pretty nice and as i'm in the market for a new one thought i'd see if you were on here and what one it was . .
Okay when I asked for an explanation I was told when he replaced the rear discs he cracked an abs ring and that's why the light is on. Would it come on if that was the case ?
When viewing a Clio sport this morning one thing I pointed out to the owner was the serv light being on. He said when he took it to a garage to find out what was wrong they said it just needed to be reset etc. This car is on just over 36k and has not had the aux belt done yet, would this be why...
I went to see this before it was repaired. Had been shunted from the rear and the guy was fixing it. The engine was sweet as a nut and interior were as new though with that mileage.
Oh and standard 182 not trophy as you all know.
I am currently looking to sell my FK konigsports and would like to know what clio's they will fit so i don't mislead anyone etc.
The hole spacing is 52-58mm as the top hole is elongated as pictured.
Cheers
I have found a set of BBS alloys for sale and am unsure if the centre bore is correct for the clio. The seller has told me they are tapered from 70mm to 55mm with the main hole being of 55mm diameter. They were fitted to a golf mk2 which i believe is 57.1mm centre bore so i'm not sure.
Also...
I am currently looking for a new set of tyres to fit my new 14" wheels (6j width).
I would like them to be as low profile as possible and the lowest i have found so far is 195/45/R14. Any others i should consider ?
In the above profile i have found Toyo T1-R and Falken ZE912. Toyo's seem to...
I am currently looking at buying a set of second hand ATS cups and am unsure if the fitment is correct for my clio (1.4 MK2).
They are 4x100 which is correct and the offset is either et20 or et28, both of which i believe will fit ok. However i am unsure about the centre bore size. They were...