Search results

Ok will give that a try, suppose it's best to start off on the softer setting first? though I will be doing a few track days any suggestions?

Got a whiteline ARB today, unwrapped it to find only 2 setting holes to adjust stiffness! I always thought they had 3, for soft, medium and hard, can any one set me straight? Also fitting instructions say the car MUST be at ride height when fitting. Can I not put the back of car on axel...

Got a miltek fitted with standard cat, 3 years on no issues! As above not too loud when driving normally, hit 5k onwards and it sounds pretty sweet.

Thanks fellas for the response, just wanted to double check they would be ok!

Bought a set of ph1 172 f1s back along, and i need to know can i use the wheel nuts from my 182 to fit the f1s, when i when i offered up a spare 182 wheel nut to the f1 nut hole it didn't seem to sit too well in the tapered seat? Can anyone give me some feed back? Cheers

Its all in your head! Yours looks fine too me! I,m always looking at other peoples cars thinking why do they look better then mine!

Why do the back ends of 1*2s get s*#t bound so easily? Nice colour ;)

Pikey F#*kers!

Sure i've seen the gear numbers transfer for the clio on ebay not so long ago might be worth a look?

yes really annoying especially if you have an OCD complex about paintwork like myself! Most people will never notice though!

Yes had it done today not bad! was making 174bhp/154lbft before remap.

Had sportlines fitted today! Had a longish drive after and i can't fault them, defo takes corners better, comfort not too far of cup set on normal roads and no where near as crashy as i thought they would be! Plus you get that slight drop making the car look so much better! You wont get the...

Standard 182 engine making good lbft after remap at K-tec! save your money! Good gains fraction of the cost!

Re: South West Rolling Road at K-tec Racing: 21st January1. Will. 2. Luke. 3. Bux (Deposit Paid) 4. Tom172cup 5. Daz_RT_04 (Deposit Paid) 6. Cub 172 (Deposit Paid) 7. Skeeter 8. clio172xx02raw 9. Clio_172cup36 10. Sam Bs 11. Darren (Non-member, Clio_172cup36's friend). 12. J55BUD (Deposit Paid)...

Nice! Always liked the cup with dark turinis! Got sportlines going on at the weekend! ;)

Ok mate much appreciated!

Going down to k-tec this coming sat(14th) for service and sportlines, whilest i'm there was gonna inquire about having a remap and when they could fit me in next? If I can't booked in for a little bit, I wouldn't mind coming along on the 21st just to meet some members and see what mines putting...

Going back afew years before i bought the 182 i went down my local renault dealership to look at a sliver 172cup the salesman who took me for a test drive didn't have a clue, he knew nothing about the spec differences between cup and FF! Waste of time some traders!

Enjoy!

Re: CLIO 182 SPORT NEWBIE Sure they've got the new rolling road set up now! Think most standard 182s when put on dyno only put out roughly 160-170bhp so 184bhp is a good result bud!

I've had lots of positive comments from other people about the colour of my RB! And they weren't homosexual! Seriously go and ave a look at one in the flesh you'll want one!

Re: CLIO 182 SPORT NEWBIE 184bhp Nice gains! Liking the effort you've put in! Going over to K-tec this saturday fot a service and sportlines. Interested in getting the matched inlets and remap what was yours putting out before they fitted inlets and remapped?

Always thought tyres or rims protruding wheel arches was illegal? plus it look sh**e!

The badges will be going back on! so will try and unclip the clio badge and heat up the renaultsport. Cheers for the info

Cleaned, clayed, polished and sealed the 182 a couple of weeks ago! But every time i do this i can never get inbetween the renaultsport and clio logo on the boot lid to clean the paintwork? Can these be removed or are they stuck on?

Always wanted an Aritic blue until an RB pulled up along side me one day!

Defo RB!! pics usually don't do the colour justice!

WTF! They are all truely shocking!

Replaced my gear knob insert last week! two minute job. flathead screwdriver lever the old one out, pop the replacement in, job done!

4" back bore exhaust on my old s2 RS turbo! would wake up most mornings to find someone had stuffed a 2 litre coke bottle up it! lol