Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!
Hi all.
My friend who is an keen Renault head has recently decided he'd like to have a go at doing some.car review videos. He's only done a couple but would apreciate any constructive cristisicm or pointers. Take a watch.
RenaultSport Clio 182 Review - Budget Drivers Car...
What is the best way to route the positive cable through the cabin from the boot? I have a full interior.
Id have the battery box passenger side in the boot, cable could go down by rear seats behind rear door card and along the plastic sill trim and up behind the dashboard? Is there a suitable...
A C16valver meet, but always open to Cliosport lot to help raise the numbers :) Just write on the list here and ill update it to keep it in sync with the one on C16v forum.
1. Bass - Clio 16v Turbo (Clio16valver.co.uk)
2. Peter - Clio 1.8 16v (Clio16valver.co.uk)
3. JayKay - Clio 2.0 16v...
Just got a repalcement set of seats but want to clean them up as much as possible before swapping them over. I know nothing about interior valleting.
I dont own a wet vac or anything like that, is there some effective method useing products i can pick up off the shelf?
Thanks!
Posting up here as some of you might have some mates with AUDI, Seat, VW 20VT's e.t.c
http://www.ebay.co.uk/itm/140991358708?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649
Thanks
I've had a rageing hissy fit and managed to bend the tabs on the passenger side airbag on my 172 cup. Also the 3x screw holes are threaded so the dash doesnt screw in tight.
My mate is splitting his cup so i might use his airbag, are they coded to the car or are they just plug and play?
I've looked around on the net for many hours at this topic and come to no real conclusion.
Im currently rocking some Audio Technica WS55i, which are great for everyday listening on the iPod on the way to work e.t.c But i would something a little more 'uprated' for listening at home.
I've...
Do they use the same piston ring set as normal F4R pistons?
They have the same 82.7mm diameter, with 2 compression rings and 2 oil scrapers and a control, but are the rings the same thickness?
Thanks
Organised on Clio16valver. But the more the merrier. (+ could do with cliosport to make the numbers to be fair).
(Clio 16valver)
1. Laine
2. Bass Direct
3. Jaykay
4. valver16
5. Squeak
6. Paddy
7. big mike
(ClioSport)
1.
Do you need to be houdini to do this? Will be fitting a GEN90 shortly, and remember having a go at this randomly when my engine was out once, is there an easy method without damaging or bending anything?
Need to put a boost gauge inside the car, without drilling the bulkhead/firewall does anyone know any convinient placed to put a small boost pipe through? THe best i can think off is through the acclerator pedal grommet (which isnt used on the ph2 RS), but do i have any other options?
Thanks
I am led to believe the Cup radiator is slightly slimmer, could someone measure theres for me please (just the width).
I want to relocate my oil cooler behind the cross member (so its not sitting directly behind the intercooler), but the radiator is fractionally too fat, and im wondering if a...
Im wiring in a R21 2 bar map sensor for my low boost conversion. I know the pinout for the GM sensor, but i do not for the 172 wiring loom.
Can anyone tell me what colour wire is for power, ground and signal?
Thanks
Thought i best post here :)
Had my cammed cup for a while and enjoyed it, had many different engines in the past with renaults, ITB's e.t.c but never had any boost, a turbo kit came up for sale on here so i bit the bullet, drove to Wales a couple of weeks ago and collected it.
Below is just a...
Help, just put my rebuilt engine in the car today.
Engine cranks over fine but it will not fire, not even a splutter. I have put the multimeter on coil pack plug and injector plugs, they arent reading anything (not firing), apart from the crank sensor (which worked perfectly before i did the...
Dismantled the block to repair the engine the other day, the headbolts i took out (the original renault ones), were bone dry.
The replacements have come in an oily bag (presumably to stop them corroding in storeage). Renault states to oil headbolts only when re-using them (which im not). Should...
eBay is useless, Google is usless. GSF and ECP cost a fortune and would probably send the wrong alternator.
Is this something to get through a speciliast only, or renault? Or are there some good autoelectrical websites hidden on the internet somewhere that i cant find?
Just removed the air con stuff from my Cup, the last part to come out is the rad unit from the blower unit. I can't for the life of me figure out how it comes out, the whole unit is really shoe horned in. Has anyone else done this before or is there a guide anywhere? I dont want to leave it like...
Who here has had them fitted and mapped, and what were your results please? I've not found a definitive thread about these cams yet.
I know theres a chap with a black 182, but im sure there are a few more of your out there? Seriously considering a set of these cams. WOuld like to see some graphs
Bought my cup a while back and put it on the rollers yesterday at Surrey RR with a few others, was pretty shocked at the result considering it only has a panel filter and Ktec exhaust. Standard map and cat convertor too, and its an aircon model! THis is nothing more than a happy thread :D