Search results

I thought i would start posting on here as it seems to have a bit more activity that a few of the others, this is a summary of the megane build so far. I had been on the look out for a LY R26 for around 2 months and finally purchased one from my friend craig on april 3rd 2016 however weeks...

Hi guys, just undergone a 197 brembo conversion and my pedal travel is a lot longer that it use to be, currently running a cup mc on the ph1. I flushed the full system and used an eezibleed to bleed the brakes, reading a lot online tonight it is apparent that air can be trapped in the lower...

Hi, Can anyone with a set of rear 1*2 flexi's measure them for me please if you just have hem laid on the bench or parts pile, I need to get some made up in braided and just need a length. I did do a search but couldn't find any info on the rears. Thanks guys

Hi guys I have a electrical fault with my ph1 172, car wouldn't start totally dead so put a new battery on, still wouldn't start but would bump off, checked the relays and swapped them about and checked all fuses and they are ok. Put a new starter on and now I've gone to connect the power and...

Hi guys, currently planning an abs removal, I have a cup master cylinder and ford pressure reducing valves. First off is it just the two nuts under the master cylinder holding it in place? My plan is the run the two front lines from the two front ports (closest to the engine) and the two rear...

Hi guys, food for thought, Running a rotrex c30-94 and epas, I can't use a pms pas delete kit as they say it doesn't work with standard pulleys however does anyone know if I can run a 1.2/1.5 clio pas idler instead from the mk2 ph2 setups? Thanks in advance

Hi guys, looking to hold a decent meet that everyone will enjoy, in the past we have had meets at the ok dinner on the A19, a BBQ at hamsterly forest and a meet at Penshaw monument, can I have your suggestions?

Hi guys, ive read every thread i could see and none of them have solved my problem. It's an intermitant fault which is most annoying. car cuts outs only every so offten at junctions, can go for a blast come to hault then try to pull away and it will stutter and then cut out. i cant think what...

Hi guys, I have a stutter occuring at light loads between 1500-2500rpm around 30-40mph on my ph1 turbo And idea's? The injectors all read 14ohms when checking resistance, however this doesn't cancel them out as being the problem. It has a new adaptronic coilpack, new r26 genuine plugs, new...

Can somebody send me the 172 workshop manual please? Email is applekirk@googlemail.com Thanks!

I have a sticky idle on the ph1 and after cleaning the throttle body and replacing the throttle cable it still appears. This thinking it's the icv, I have searched the forum but there's a few contradicting threads, if I put my thumb over inlet to the idle control valve and it tries to cut the...

Has anyone had this problem before? it's on a ph1 172, ignition on only, try to connect it to the car it's days the above but then the bottom of the window comes up as connected. It also reads the fault codes but cannot delete then, and it is unable to read the ecu. Anyone any idea's?

As above really, does anyone know the size and pitch of the rear carrier bolts, they hold the carrier on.

Does anyone have a cad drawing of what can be removed from a standard flywheel? k tec offer one at 3.9kg's from 5.3kg's so im just wondering what would be the best for a road car. It will be took to a machine shop to do properly but a cad drawing of the maximum allowable material that can be...

I have a ktec stealth that is making an awful rattling noise, I pretty sure the baffles in the back box are rattling, is there an way to fix this of new back box needed? Cheers in advance?

I've installed a polo radiator for my throttle body setup but now the temp on the dash does not get to half way it sits about a dot below, the fan doesn't kick in so that's not keeping the temps low and the thermostat is working? Has anyone else had this? Cheers

What's the best way to get a drain in whilst using a ph1 drive shaft, just run a threaded an10 90 degree bend and tap the sump? Ideally I want the drain vertically below the turbo? Or is it necessary I run a 182 shaft?

I have read over throttle body threads but can not find a definitive answer, in regales to the breather that sits into the 172 inlet manifold, when using a custom inlet or throttle bodies people have the coilpack bracket mounted above this, do they block breather and just let the engine breath...

Have searched but all I can find is the torque setting of 55nm, I need to know what pitch thread and length please?

What do the f9q brackets come on? Is it just any tdi megane scenic or traffic van? Also anyone know if it's possible to run a renault 11 alternator tensioner bracket so I can remove power steering pump and just run a Clio dci assisted steering Colum? Thanks

As above, white 197 had recaro's, may of been a cup. 2pm in the big car park, just wondered if it's anyone off here?

Ever since I converted to the cup alternator setup I've had starting problems, replaced the battery and it was fine for a month untill today. Got in car, wouldn't start but did bump off, checked volts with multi meter, 10.8 when running but if opened throttle rose to 11.8 and rose again when...

Don't know if the owner is on here but i see It quite often, hitting the top of third in a 20 zone is not big or clever, you are a t**t.

After fitting a cup alternator setup to my ph1 I am not happy with the bend in the power steering line to avoid the bracket, I am going to have a small braised flexi line made up for between the pump and the connection just after the sensor. Does anyone have the sizes for the pump, and the...

So I plugged my car into a friends rs tuner and a fault whilst connecting kept occurring so I could not actually access the ecu. Anyone have this problem? I have followed all procedures, it's not something stupid like forgot to turn ignition on. The cable was abit awkward to connect, is the...

As above either of oem or solid, whatever anyone has available?

[IMG]http://img.tapatalk.com/5609b1dc-a945-85d0.jpg[/IMG (Sunday morning) Uploaded with tapatalk If anyone wants the full size hd image give me a message and I will send you it, have a lot more on the other...

Just bought another ph1 as a track car, however after taking it for a blast there is oil up the back end. Steamed everything off underneath and thought it was the sump so removed it and put a new seal in, after another blast out it seems there is oil still on the rear after cleaning the...

eBay advert Ends today http://bit.ly/NftOUs

So, i finally bought a ph1 after getting ultimate gip and abuse of craig and kris on here, and the insurance is sensible(ish). I went down to Peterborough (about 140 miles away) to go buy what seemed like a 'mint' flamer, however when we got there it was absolute mess, with dents in either...