ClioSport.net

Register a free account today to become a member!
Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

  • When you purchase through links on our site, we may earn an affiliate commission. Read more here.


Crayola

ClioSport Club Member
Why will I have to redrill them? the seats should bolt straight on the holes already there shouldnt they?
Yes they should

However, they do not😂😂

Started mocking up my buckets. I found a few bits wrong/annoying

Firstly, because in a fat c**t I have to get XL seats. Because they're XL they dont line up with any holes on the subframes??

View attachment 1413134

Secondly, the previous owner of the seats failed to mention the part where he snapped off one of the mounting bolts in the seat. So yeah, cheers

View attachment 1413135

And annoyingly it's the one I wanted to use as the drivers seat as it's still in FIA date until 2022 and the other one runs out this year and has a heat gun burn mark on it

Never the less I needed to get one in there to love the car about for the time being. It's a tight squeeze when I placed the seat sort of where I wanted it

View attachment 1413136

I came back to it the next day because adult duties called?

Started out by laying some tape and marking out a few places where I need to mount the side mounts to the subframes

View attachment 1413138

Measured 3 times and then pressed on by drilling holes all over the shop?

This hole goes through the sidemount, subframe and then uses the existing but underneath as the bolt would make the subframe rock if not.

View attachment 1413139

I'd just hovered it and I couldn't be fucked to remove the subframe again so out came an old sheet?

View attachment 1413140

Then my punch started enjoying me so I stuck it in the drill and sharpened it on the grinding wheel. Now I dont have to worry about it sliding all over when I'm trying to stamp a point!

View attachment 1413141

Got all my holes drilled and the sidemounts in place... I messed up at this point too. I spent 10 minutes bolting everything down like this...

View attachment 1413142

Then forgot that I'd not stuck the seatbelt in!?☹ doh

View attachment 1413143

After all that I got the seat in and I'd raised it and brought it a little more forward than I first anticipated but it feels better for it...
This should give you an idea of the arse ache I went through
 

Eddie555

ClioSport Club Member
  Q7 2018 & 172 Cup.
I've got OMP ChampR (slim fit) as my passenger seat and OMP RS-PT (wider fit)for drivers seat both on Jon Foz plates. No problems fitting either of them, all the holes were perfect..

Sent from my SM-G977B using Tapatalk
 

DomP182

ClioSport Club Member
  ph1 172, Arctic182
Got a few photos of starting on deep cleaning the interior, rust preventing inside the rear arches/sill bits. Just waiting on the Hydrate 80 etc.
View attachment 1469218
View attachment 1469219
View attachment 1469215

And also test fitted the Jon Foz Subframes ready for my new Corbeau Clubsports that are on there way.
View attachment 1469214
View attachment 1469217
Wow an old black and decker electric screwdriver or is it a bosch? Also what's the fork for?
 
So today I got the headlining out ready to retrim in alcantara
IMG_20200426_113601_019.jpg
 
Lots has changed over the last year.

IMG_20210104_151033_488.jpg


Gas bonnet struts
IMG20210212122257.jpg

BMS
IMG20210219202537.jpg

Just got to finish off fitting the BMS and making it look tidy.
 

Attachments

  • IMG20210118135155.jpg
    IMG20210118135155.jpg
    1.9 MB · Views: 41
  • IMG_20201224_170431.jpg
    IMG_20201224_170431.jpg
    1.9 MB · Views: 46
  • IMG_20201224_170620.jpg
    IMG_20201224_170620.jpg
    1.7 MB · Views: 41
  • IMG_20201224_170655.jpg
    IMG_20201224_170655.jpg
    2 MB · Views: 43
  • Like
Reactions: LOK


Top