ClioSport.net

Register a free account today to become a member!
Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

Search results

  1. M

    KTec ITB throttle linkage sticky? Better spring?

    Glad someone created this topic! I've been running ktec bodies for 5 plus years and had the same issues. I fitted spring to top of the pedal which gives a much nicer pedal feel and cured the same issue
  2. M

    172 Cup blower into a 182 Cup?

    Just so you know, my car is 182 cup so heater element swapped over no probs
  3. M

    172 Cup blower into a 182 Cup?

    Hi there, It's been while since I did it. It is so easy. Cup blower goes into same place as old one. Blank off the rectangular hole left by drivers side in bulkhead. Take off heater element from 182 blower and fit/replace onto 172 cup blower. You may have a spare plug left over, I can't remember
  4. M

    GEN90 Ecu connection problems

    Do you have the usb dongle that goes with the cable? Sent from my SM-G935F using Tapatalk
  5. M

    Throttle bodies help

    Yes you need gen tuner to set tps position. There are videos on ktec website on setting up bodies. I'm using 421 catcams on meg 225 injectors. Rs 192 exhaust decatted. I'd say your realistic expecting 195-200bhp Injectors will be running near max potential. 225 injectors I've read have a better...
  6. M

    Throttle bodies help

    Hi there, I have the same itbs. Is the cable too tight? If the idle screw is wound out it would tickover very low. That tell me you need to undo the locking grub on the cable and allow for some slack. In addition to this I wasn't happy with throttle cable. The springs don't feel strong enough on...
  7. M

    Battery relocation gone wrong!

    Good news is battery is fine and alternator is fine, bad news is I'm a dope! It was a poor earth
  8. M

    Alternator issues

    Multimeter, back of the Alternator off the live and earth by bolt on engine mount. Also checked voltage off battery 12.7v Sent from my SM-G935F using Tapatalk
  9. M

    Alternator issues

    Surely a brand new alternator can't be at fault especially a good cameo one from Renault parts
  10. M

    Alternator issues

    Hi guys, I'm running 172 cup alternator setup. The car died on me suddenly lost all power and drained the battery (Odysey pc680 in the boot). Changed the alternator for brand new valeo from RPD Voltage output is very high using Odysey pc680 ranging from 15v-19v on tickover Used the original...
  11. M

    Battery relocation gone wrong!

    Battery is brand new, fingers crossed it seems to be charging, after 2 hours it's at 11.7v Sent from my SM-G935F using Tapatalk
  12. M

    Battery relocation gone wrong!

    Grrr I have just this minute connected old battery up and as soon as i did a horrible smell is coming from back of alternator. Started the car fine, tested back of alternator red lead to live and black lead to earth. Fluctuating readings including up to -6v and also checked battery end 10.3v...
  13. M

    Battery relocation gone wrong!

    Here are pics of said wiring and farthing point. Bit of a bodge using the eye but I thought it would be good for an earth point Sent from my SM-G935F using Tapatalk
  14. M

    Battery relocation gone wrong!

    I'm in the process of reverting back to the old battery for now. I took a photo of the cable used. It's 6mm in diameter which equates to 28mm2. Not small?! Earth was the old battery earth from under bonnet. Will report back once I get it fired up and test the alternator. I HATE ELECTRICS Sent...
  15. M

    Battery relocation gone wrong!

    It is yes I'll measure it. Earth strap is marginally smaller? Earth is bolted 12 inches from battery using one of the old rear seat belt anchor bolts. Never struggles to start . I'll check alternator tomorrow evening and report back. I'm hoping I can charge the battery and it's ok?!
  16. M

    Battery relocation gone wrong!

    Hi guys, Bit of a strange one. So I have very recently relocated my battery to the boot using an Odysey pc680. Did a nice neat job and using a thick wire. Not had any problems. It's done about 80 miles. However almost got home today and the dam thing was firing on 3 cylinders and in the end...
  17. M

    North west meets??

    There's a meet being arranged on Facebook by Steffan Hansen and Liam Steer? on Facebook page "north Wales Renault sports owners"
  18. M

    Large Port Head

    It's been said bigger isn't always better with port sizes on these heads. People like pure motorsport specify small port heads on exchange, think ALD might have touched on this also but don't take my word for it.
  19. M

    Jenvey throttle body setup (balancing the bodies)

    Top work! Not a difficult job at all. Forgot about the ktec videos. There very handy Sent from my SM-G935F using Tapatalk
  20. M

    Jenvey throttle body setup (balancing the bodies)

    Ktec bodies are jenvey. I think idle will be done from the throttle springs as the butterflies are now cable operated. I'm not an expert but logic says tick over will be controlled from the bodies not ecu. Can you post a better pic of the bodies showing the cable setup and how each body is...
  21. M

    172 Cup blower into a 182 Cup?

    I have done this also. I used 182 element in 172 to retain the plug. Easy mod
  22. M

    Jenvey throttle body setup (balancing the bodies)

    Air flow readings depend on tick over speed. Balance them out and adjust tick over to wherever your happy. Sent from my SM-G935F using Tapatalk
  23. M

    Jenvey throttle body setup (balancing the bodies)

    Hi there. I have ktec bodies so balance slightly different but this should help. There might be an air bleed screw on each one. Ideally as they are individual bodies they should have an adjustment screw via throttle linkage. Should be fairly easy Sent from my SM-G935F using Tapatalk
  24. M

    stop, serv, airbag light after bucket seats

    I took them out of mine as I converted to 172cup brake setup and buckets. Just oil light left [emoji16] Sent from my E6653 using Tapatalk
  25. M

    stop, serv, airbag light after bucket seats

    Take the clocks out and remove the leds. Not a big job Sent from my E6653 using Tapatalk
  26. M

    Wiring loom modification

    Dam, I'm just about to start stripping my loom back. Still using key c/l and alarm Sent from my E6653 using Tapatalk
  27. M

    Wiring loom modification

    What does the uch operate? Sent from my E6653 using Tapatalk
  28. M

    [Jul 2, 2017] EVO Triangle Run - Sunday 2nd July 2017 (Bala Watersports Park)

    Due to my piss poor timing I won't make it. Just taken recaros out and in the middle of fitting bucket seats and harnesses. Won't finish in time. Seats going for sale today tomorrow or Sunday in for sale section
  29. M

    [Jul 2, 2017] EVO Triangle Run - Sunday 2nd July 2017 (Bala Watersports Park)

    Im hoping to come to my first meet, what time are you expecting to get to ponderosa?
Top