Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!
Hi Guys.
My brother bought a cambelt kit before for a Renault but bought it for the wrong engine. I want to advertise this on Ebay but we both cant remember what engine it was for.
Could someone please cross check the Renault part number and tell me what its for please?
The number is ...
I am using a valver ECU for my 1.4 8v renault 5 fuel injection project. To do this i have unsoldered the ROM chip that has all the running data programmed to it and have soldered a socket in place so i can write my own chip to run the 1.4 engine. I need to test that my soldering is good first...
Following on from this ... http://www.cliosport.net/forum/showthread.php?554988-R5-GTT-Fuel-Injection-Build&highlight=
I have a 1.8 16V Valver ECU that i need testing, in short i have unsoldered the ROM chip, soldered a socket in place and pushed the original ROM that i removed back into the...
Hi Guys,
Trying to work out if i am going to need an External Fuel Pressure Reg or not.
Building a R5 Gtt C1J lump but with fuel injection, and obviously its turno charged.
Want to run 3bar standard, so hoping the standard pump and the reg is rated to 3bar?
Could someone tell me what the reg...
My car is in major need of a bottom end, and think i have found a tidy one! its Rob91's. Was going to buy his entire engine and drop it in but he is now splitting it.
His engine was a 1.2 16V engine, and mine is a 1.2 8V engine.
Could i use my head on that block? the CC is the same, just not...
Need to replace my current 1.2 8v clio engine because the rings have gone, and along with other problems, its just cheaper and easier to swap the engine.
Have been offered a 1.2 16v engine, gearbox, looms, ECU, clocks etc for a VERY good price which i cant really let go to someone else.
Just...
Decided to launch a new project, had this idea in my head before but never went through with it because of money. Although i am still only receiving EMA from going to college, i have a few interviews coming up, and also just left a lifeguarding job and looking for another, so hopefully will...
I have a 1.2 8v 2002 ph2mk2 clio, and want to run 172 brakes all around, becuase they are disks on the back etc, ready for when my project engine goes in.
What beam do i need? can it be any 172 beam?
Cheers.
Had the cambelt snap about 4 days ago, picked up a new head gasket, Cambelt and some sealant, valves and pistons were fine so i rebuilt it back up following the book.. The bottom line on the pully was facing down to the ground (in line with the casing mark) and the line on the belt, and the mark...
Was coming around a sweeping bend going down hill, went into third and jumped on the throttle to power out/down it, and nothing, absolutly nothing, engine was off.
Didn't stall or anything, no thuds, bangs, vibrations, music was on Quietly! didn't even notice! .. pulled over, hazzards on, just...
Basically i plan to remove my ABS system, and just run brakes straight from the master cylinder. My car is a Mk2Ph2 1.2 8V 02 clio, does anybody know what master cylinder i am going to have to buy?
Also, does anyone know what break line line i would have to buy, as i imagen its a certain...
Image pinched from "Wocka"'s post, hope you dont mind.
The hole underneath a 172 inlet manifold? .. Going to be cutting one up shortly to use the plenum for a R5 GTT Fuel injection conversion, but didnt know this hole was here, whats it for as i will have to weld a plate over it?
Cheers.
Hi guys,
I believe my valve stem oil seals are passing oil as i have to put about 2L's of oil in my clio per week (i do about 1000 miles a week), I know its not leaking it as i have checked and can see blue smoke out the exhaust and smokes like mad every now and again, exhaust is oily so i know...
Right still doing this wire tracing, managed to locate the oil pressure sensor, so i put my multimeter end into the connection for it, and then tried every pin on the main engine loom connection til i found what one it was, then i labeled it.
Then i did the same with the Water Temp Sensor and it...
Can anyone tell me where the Oil pressure sensor is located on my engine please?
Is it the one to the left of the tip stick tube, just above the sump?
cheers.
Right, just over half way in to converting a F7P loom ready for a Renault 5 GT Turbo fuel injection build i am currently doing.
I would like to keep the standard clocks in place, so i need to run a rev counter signal wire to the main connection block which is no problem, does this mean i just...
How does it work? as i have to put this connection into a project loom i am building..
Im guessing that one of the 2 wires goes to power? and when the car is put in reverse the switch makes the connection and passes the power along?
Can anyone confirm that this is correct?
Hi guys.
Currently looking into removing the entire ABS system and just running normal brakes, as i think you get more feel for whats going on, also it would have to be removed for the engine conversion i am planning (Fuel injected Renault 5 gt turbo engine)
Only worry is that my speedo comes...
Right, i am currently in the middle of doing a R5 GTT EFI conversion into a PH2MK2 clio.
I have used a F7P loom and have stripped out the wires that are not needed.
I have to solder the main engine loom connection to the converted EFI R5 GTT Loom to mate with my clio.
Now my question is, what...
Right i think my clutch has pretty much had it, was slipping a bit earlier on a big hill and biting point is right at the top of the pedal travel, only have to push it down an inch to change gears, so going to buy and fit a new clutch tomorrow.
Anything i should be aware of? i know one of the...
Hi guys, hope all is well.
I have to change the valve stem oil seals on my clio as they melted and are leaking oil as my car over heated.
What is the best way to change these? i dont really want to have to take the cam belt off and the head off to be able to do it, i have machined an adapter...
Hi all,
Thinking of selling my current clio, and getting a ph2 2002 172 in jan/feb, just wondering if there will be any companies that will cover me on insurance, and if they will what kind of quotes i would get?
Went on go compare for a quick look just to get an idea (even though its always...
Hi Cs x .. Hope all is well.
I was driving through the village i live in, when i spotted the police, i am very good friends with them so pulled over for a chat. We had the chat and they went on their way. I walked back to my car, jumped in, went to start, ignition come on ... Nothing strange...
In January i will be buying a PH2 172, so just picking up a couple of bits here and there so when i get it i can just start changing it to how i want it to look the day its mine.
Just wondering, on the indicator bulbs (front and back) are they the 581 offset pin bulbs like these ones?
Cheers.
Just wondering what wiring kit i need for my audio set up.
Here is the head unit i am using..
Here is the amp i will be using...
http://www.halfords.com/webapp/wcs/stores/servlet/product_storeId_10001_catalogId_10151_productId_768519_langId_-1_categoryId_165526
and here is the sub...
I want to use 172 front and back brakes on my ph2mk2 clio, its a 1.2, as many of you know i have intentions of putting the F7P turbo engine into it when the car is ready. Shouldn't be to hard of a job because i will be removing the ABS, and running a 172 cup master cylinder straight to the...