Search results

Hi All, Hope you like it !!! Just clayed plus Collinite 915 waxed.

Hi all, Just got me a set of 16" OZ f1 cup's. What is the best tyre size for a ph-1 172? 195-45-16? Thanks in advance.

Hi All, Launch control algorithm has been successfully implemented in Sirius ECU by Henk@FASTCHIP. I have found this very useful while launching for a sub 200 HP FWD car. Here is a sneaky peek while it is under action Cheers Alper...

Hi All, Clio RS Mk 1.5 from Turkey.

Hi all, As above, need a picture of clio 172 inlet manifold with gaskets on. Cheers

Hi All, As title says knock sensor part number needed for Clio 172 ph-1 thanks

Recently my drivers seat will not slide forward to allow people in the back. Anybody has any pictures showing the mechanism, any suggestions. If anyone who has had this fault please can you PM me or reply here Thanks,

As above, jc5-129 (cup gearbox) & jc5-089 (ph-1 172 gearbox) pics needed. if possible, the connection points on the gearbox (frontal view) Thanks

Hi All JC-5 089 (Ph1 172 gearbox) JC-5 129 (Ph2 172 gearbox) Any other differences than the differential, Is JC-129 gonna be a direct fit to Ph-1 172?

as title ?? would it be a direct fit to the 1*2's ??

Finally, Car is 2000 Mk1 172 Mod list C&B cams k-tec full zorst ITG maxogen k-tec 4-2-1 manifold + linking pipe matched inlets plus plenum Of course most importantly Henk's fully custom .cal file Here is the result 128kW = 174 HP ATW 195.25 Nm ATW Torque

Hi All, I got Innovate LC-1 and SSI-4 all hooked up with. I need to log TPS data. What is the easiest way to do it? Off ECU or splicing the loom (three cables coming off the potentiometer, which one is alive?) on the butterfly potentiometer? Any other suggestions are all welcomed? Best Alper

water pump for clio 172 Mk1, part number requested? Thanks all

Hi All, Anybody knows the renault part number of part 1 ? I drive a Mk1 172 CB0M Thanks

Hi All, ph-2 172 rear wheel arch liner part number needed. Thanks

Hi All, After my RS, I decided to get my dad's car remapped, of course the person to visit is Henk. Car is totally standard including the cat is still on. It was superchipped 4 years ago, at those times RSTUNER was not available and Schips was my best bet. I always observed some kind of revving...

Just bought these, Many thanks to Maurice from MBEngineering, awesome built quality. Not have a chance of fitting them, will be very soon.

Hi All, How do they work on Clio 172? I checked the std one's on my car are running at 91 % injection duty cycle at high RPM's. Car is not std and running on cams btw. Thanks

Hi All, I am looking for a 4" to 2.5" (100 mm to 70 mm) silicone straight reducer or 90 degree elbow for an induction set-up. Anybody knows where can I supply? Thanks Alper

Haha, Look at what this guy did :)\ OMG !!! r****d :) ''Alright, after reading a ton of threads on welding up gears for extra traction, i went ahead and welded mine up. I put the third back in and went to pull out of my garage, and I just roasted my clutch. I figured that...

As title says would you post pics of ph1-172's with ph-2 172 rear bumper. especially silver one's. Thx

Hi Guys, Drive a Mk1 172, Here is the problem, not happens very often though, oil level reader of the road computer shows ------ oil. I checked the oil level by the stick, level was normal. When it does that SERV light also flashes. Where could be the problem? Oil pump or the...

It was very hot outside around 36C but still gave a shot. Awesome low-down torque even with the C&B cams. Mod list C&B cams RSTUNER PRO 4-2-1 Ktec headers + decat pipe Ktec stealth centre section + REMUS backbox ITG panel Special thanks to Henk for his custom map.

Can anybody tell me what is the nominal size (all the details needed, thread size and etc.) of the original head stud on F4R-730 (Clio 172-182)? Just checked it on ARP website, they do not specially make it for Clio but there are many universal one's. Thanks

Would the Clio 172 cams fit to the other F4R's such as 140 HP IDE's? Thanks

Just gave the car a nice clean today. Enjoy.

As can be seen from the title, I need the inner diameter of holes (bore) where the piston sits? Can anybody be kind of to measure it for me? I know the dia of the pistons but not a chance of getting the head gasket one's. And also how thick is the original head gasket? I know it is MLS so...

Thinking about getting these, what are the cons and pros? anyone using them? Clio 172 http://www.catcams.be/datafiles/docs/springsetup55024xx1.htm RENAULT Clio RS O.E.M. parts CUSTOM parts / SPORT [2.0L 16v dohc rprh] IN EX IN EX upper retainer O.E.M. O.E.M...

Hi All, Can anybody tell me where this socket is supposed to be plugged in? Photo was taken from some area inside the car under the dash. Most probably an UCH unit Thanks

Clio RS 60-120 mph video, it was windy outside, sure can do better :) ENjoy mods, RSTUNER Live MAP + Colombo BAriani cams + Hill Power Bent + ITG etc etc.. http://www.dailymotion.com/en035/video/8989034 It is the only European 172 with UK instrument cluster :)